Just to let you know the one you linked has almost as many 1 stars as 5 stars, so it probably isn't that good... And why do 2 cost 5x as much as 1 rivet gun?

Position the lower jaw of the pliers (the side with the hole) over the mark and make the punch.The wire must fit snugly into the holes you have punched into the blanks to form a good rivet. The pad will cushion the punch while allowing you to clearly see the mark where the hole is intended. The riveting process is noisier than welding due to hammer blowing. With the Sharpie, mark where you want the rivet to be on the top blank.Use a Pro Polish Pad to avoid marring the metal.

This will flatten out the rivet head and give it a nice smooth surface. Step 21. I run commercial headers making specialty bodies. The head should be pushed firmly up against the end of the gun.

BHS HOT JET® BHS HOT JET ® is a hot air riveting process, and is also a “single-step process”. The pop rivet pliers are used to pull the pin through the rivet and as this happens the rivet is deformed slightly so that it joins the metal or plastic pieces. The mandrel can be thrown away after you're done.

"Will you lend some examples of your uses for the pins? 1 year ago

Place the wire into the holes of the stamping blanks, you want about 1/8""-1/16"" overhang on each side of the hole.With about a 1/8""-1/16"" overhang on both sides flush cut the other side of the wire.Stack all of the pieces to be riveted on the bench block and insert the cut wire or rivet through both blanks.Using the chisel-shaped end of your riveting hammer lightly tap across the rivet.Turn your piece 90 degrees and continue lightly tapping across the rivet. It would help me if you had a photo of how the tool is actually used/placed on the materials. You have completed your riveted piece.You have successfully subscribed to email messages from Fusion Beads Inc. POP is actually the name of the original brand that invented and marketed these types of rivets. This will flatten out the rivet head and give it a nice smooth surface. Using the chisel-shaped end of your riveting hammer lightly tapping across the rivet.Turn your piece 90 degrees and continue lightly tapping across the rivet. In the United States, inventors such as Carl Cherry and Lou Huck experimented with other techniques for expanding solid rivets, such as the pull-through method.

9. Drill out holes ... Making sure that the gun and the bucking bar are on a straight position, press the trigger and start the riveting process. I tend to keep them as they are useful little pins that I've found dozens of uses for over the years.An important tip that you should keep in mind is that when joining plastic, you should use a washer on the inside face of your work piece if you can.

Steps 1. Riveting is a basic cold connection technique that enables you to connect metal to metal without adhesives or heat. It was quickly adopted by the aircraft industry. As heating, melting, shaping, cooling and removal steps are carried out using one tool, this process is also known as a “single-step process”. Come join me on my YouTube channel!

Pull on the gun's trigger to pull the mandrel through.

10 months ago on I learned a lot from this Instructable! 1 year ago The size of the rivet will define the hole that you will need to drill.You'll start by drilling a hole through your two work pieces. You can measure the depth of your materials with The blind rivet gets inserted into the riveting gun via the mandrel. 1 year ago Punching sets contain six removable steel punch points at of diameters from 1.9 to 4.7 mm. The action of pulling the mandrel through the tube of the rivet flares out the "blind" side of the rivet, which is on the other side of the work pieces.

The riveting head is fitted with a nozzle-sleeve combination.

This will lock your rivet in place. Professional rotary punching pliers 3230-00 Punch (punch point) A punch is a steel tool through which you can cut a hole for the rivet through two thinner materials superimposed at the same time. For complex machinery, this could be a huge hassle as it would often mean that whatever you wanted to repair had to be disassembled.The process for riveting is based on a pulling motion, and the fact that the rivet is made from a soft metal. You will start to see a small head forming on the rivet.Turn your piece 90 degrees and continue lightly tapping across the rivet.Turn your piece 90 degrees and continue lightly tapping across the rivet. A straight metal piece is connected through the parts. This will flatten out the rivet head and give it a nice smooth surface. This will ensure that it doesn't remove any unnecessary material from your work pieces. This flaring action binds the two work pieces between the rivet head and the flared blind end.That being said, it is likely that your needs will be fulfilled by a simple Aluminum rivet with a domed head.Rivets come in different gauges, which means that you have an assortment of options. We are represented by the IAM machinist union and are located in western Kentucky. Select a drill bit that is smaller than the hole which your rivet is positioned in.